http://https://www.lead1pass.com/Dell/DSDSC-200-practice-exam-dumps.html (120 Q&As Dumps, 30%OFF Special Discount: 30free )

NEW QUESTION NO: 7
Which three items should be entered to generate a SSL certificate? (Choose three.)
A. DNS Host Name(s)
B. Storage Center Management IP address
C. DNS Server IP address(es)
D. Storage Center eth1 IP address(es)
E. Storage Center eth0 IP address(es)
Answer: A,B,C

NEW QUESTION NO: 8
What is the first sequence of commands that should be used to initialize and SC8000 system after connecting the serial cable?
A. shellaccess developer
platform init hsn set ##### (Replace ##### with the proper serial number) platform init ssn set ##### (Replace ##### with the proper serial number) cs initialize
-reload
B. shellaccess developer
platform set hsn init ##### (Replace ##### with the proper serial number) platform set ssn init ##### (Replace ##### with the proper serial number) cs purge all
-reset
C. shellaccess developer
platform init hsn set ##### (Replace ##### with the proper serial number) platform init ssn set ##### (Replace ##### with the proper serial number) cs purge all
-reset
D. shellaccess developer
platform init hsn set ##### (Replace ##### with the proper serial number) platform init ssn set ##### (Replace ##### with the proper serial number) cs purge all
-reload
Answer: C
Explanation/Reference:
Reference: http://www.ens-az.com/blog/dellcompellent-sc8000-controller

NEW QUESTION NO: 9
An engineer has several servers connected to the Storage Center through two FC fabrics. The Storage Center runs in Virtual Ports mode. The engineer needs to create zones based on World Wide Names (WWN).
Which WWNs from the Storage Center need to be included in the zone with the server WWN?
A. both the Virtual and Physical WWNs
B. both the Primary and Reserve WWNs
C. only the Primary WWNs
D. only the Virtual WWNs
Answer: D

NEW QUESTION NO: 10
An engineer needs to use the Storage Center setup wizard to complete the local port configuration. The engineer needs to select a value for 'Purpose' for SAS/FC ports that are directly connected between the two system controllers.
Which value should the engineer select?
A. direct connect
B. unknown
C. reserved
D. back end
Answer: A

NEW QUESTION NO: 11
During the setup wizard, which two advanced options are available when creating a disk folder? (Choose two.)
A. Tier Redundancy
B. RAID stripe width
C. Import from External Disk
D. Data Page Size
Answer: C,D

NEW QUESTION NO: 12
A site contains many volumes that are all listed under the Volumes icon. These volumes are mapped to several servers. The engineer needs to be able to more easily manage the volumes for replay scheduling.
The engineer does NOT want to duplicate any work when assigning the volumes to a replay profile.
How should the engineer accomplish the task?
A. create volume folders and move the volumes into them, then assign the volume folder to the desired replay profile
B. create replications for each volume and use the Active Replay option, then assign the replicating volumes to the replay profile
C. create the replay profiles and assign the volumes individually to each profile
D. create storage profiles, add the volumes to the storage profile, then assign the storage profile to the replay profile
Answer: A

NEW QUESTION NO: 13
The engineer notices that iSCSI servers are NOT performing as expected. After reviewing the graphics, the engineer identifies high latency due to an excessive number of retransmits.
What is causing the performance issue?
A. The system uses the standard MTU size.
B. A VLAN ID value is set on the properties of the server NI.
C. Flow Control is disabled.
D. Switch firmware is out of date.
Answer: C
Explanation/Reference:
Reference: http://en.community.dell.com/support-forums/storage/f/3775/t/19653648

NEW QUESTION NO: 14
A deployment technician has cabled several enclosures on one chain: (1) SC200, (1) SC220, and (1) SC
280. When the deployment technician tries to configure the Disk folder, some disks are missing.
What is the cause of this problem?
A. The SC280 must be on a separate chain from the SC200 and SC220.
B. The SC220 must be on a separate chain from the SC200 and SC280.
C. A SC200 must be on a separate chain from the SC220 and SC280.
D. There are too many disks on the same chain.
Answer: A

NEW QUESTION NO: 15
In the setup wizard, which three options are available to choose how the Storage Center handles software updates? (Choose three.)
A. Search for the ISO file and download automatically.
B. Download software updates automatically and notify me.
C. Notify me of a software update but do not download automatically.
D. Download and apply software updates automatically.
E. Do not automatically check for software updates.
Answer: A,B,D

NEW QUESTION NO: 16
An engineer has configured the storage array for single redundancy across all three tiers in the system. A change in business requirements is forcing the engineer to convert from single redundancy to dual redundancy. The engineer is evaluating whether to use the dual redundant RAID 6 with a stripe width of 6 or 10.
Why should the engineer choose a stripe width of 10?
A. RAID 6-6 has a higher read I/O penalty.
B. RAID 6-6 has a lower drive rebuild time.
C. RAID 6-10 has a lower write I/O penalty.
D. RAID 6-10 has higher space efficiency.
Answer: D

NEW QUESTION NO: 17
The administrator notices that some disks show as down intermittently. The disks are all in the same enclosure.
What is the problem?
A. Each disk drive must be replaced.
B. The Disk folder is NOT properly configured.
C. The enclosure is powered off.
D. The SAS cable is NOT fully seated.
Answer: D