1Y0-A28 Latest Exam Braindumps
Question 1: The network engineer would like all HTTP and HTTPS requests that travel through theNetScaler to have an HTTP header added with the source IP address for logging on the web servers.
How should the network engineer accomplish this?
A. Enable Web Logging
B. Enable the client IP option
C. Configure the TCP Parameters
D. Enable the 'Use Source IP mode'
Correct Answer: B
6. A network engineer has configured two NetScaler MPX appliances as a high availability (HA)
pair.
What can the engineer configure to prevent failover if only a single interface fails?
A. FIS
B. PBR
C. SNMP
D. VMAC
Correct Answer: A
7. Scenario: A NetScaler appliance currently has a manually configured channel containing four
interfaces;
however, the engineer has been told that the NetScaler must now only use a single interface for this
network.
The engineer removes the channel and immediately notices a decrease in network performance.
How could the engineer resolve this issue?
A. Reset the unused interfaces
B. Disable the unused interfaces
C. Enable flow control on all interfaces
D. Disable HA monitoring on the three interfaces that are no longer required
Correct Answer: B
8. Scenario: A NetScaler engineer needs to enable access to some web servers running on an
IPv6-only network. The clients connecting
the services are
on an IPv4 network. The
engineer has already enabled IPv6 on the NetScaler. What does the engineer need to do in order to
provide access to the services on the IPv6 network?
A. Create an IPv6 tunnel and a IPv4 virtual server.
B. Configure an IPv6 VLAN and bind the required interface.
C. Create a IPv4 virtual server and bind the service group to it.
D. Create an IPv6 ACL and a IPv4 virtual server and bind the ACL to the virtual server.
Correct Answer: C
9. Scenario: An engineer executes the following commands: add vlan 2 bind vlan 2 -ifnum 1 / 2 add
ns ip 10.110.4.200 255.255.255.0 bind vlan 2 -IPAddress 10.110.4.200 255.255.255.0 What type of
IP address has been added to the NetScaler?
A. VIP address
B. NSIP address
C. SNIP address
D. GSLB Site IP address
Correct Answer: C
10. Scenario: A network engineer needs to configure Citrix NetScaler to provide Access Gateway
services to VLAN 2 using interface 1 /1 only, while also using interface 1 / 2 to provide load balancing
services to VLAN 3. How could this result be achieved?
A. Disable static route advertisement.
B. Disable layer 2 mode Create 2 untagged VLANs - VLAN 2 and VLAN 3 Bind VLAN 2 to Interface 1 /1
Bind VLAN 3 to Interface 1 / 2
C. Enable Layer 3 mode Create a Channel Interface using Interface 1 /1 and 1 / 2 Create 2 VMACs Bind
a VMAC to interface 1 /1 and 1 / 2
D. Configure policy-based routing using the Interface option as a filter.
Correct Answer: B
11. Scenario: A network engineer needs to re-configure the NetScaler to utilize two new VLANs -
VLAN2 and VLAN3. VLAN2 is an untagged VLAN and VLAN3 will require a .1q compliant tag.
Interface 1 /1 is the only interface that
will be used on the NetScaler. How could the engineer configure
the NetScaler so that it can communicate with both networks?
A. Change the NSVLAN to 3 Add VLAN 2 and bind interface 1 /1 as untagged
B. Enable the Tag all VLANs option on interface 1 /1.
C. Add VLAN2 and bind interface 1 /1 as untagged Add VLAN3 and bind interface 1 /1 as tagged
D. Add a SNIP for each VLAN Enable management access on the SNIP for VLAN3
Correct Answer: C
12. Why would an engineer want to specify a TCP Profile for a specific service group?
A. To enable use of features like SSL over TCP for that specific service group.
B. To adjust the TCP settings for traffic to and from that specific service group.
C. To use a specific SNIP for traffic to the back-end servers in that service group.
D. To enable features like use source IP , TCP keep alive and TCP buffering for a specific service group.
Correct Answer: B
